My Cart

Basic Heater 11.5kW 110V - SC117x1287

Expected to ship in 15 days

Suitable for IPSEN High / low temperature Tempering Furnaces (D/DL types) for fast and controllable hot zone heating.

Compatible Brand:-IPSEN

Compatible IPSEN part #:-KB-070580-C

Compatible Equipment Type and Size: D-5#

Packing type & Packing Qty: Foam-Box-with-woodenbox

Order & Stock Unit: PC

Minimum Order Quantity: 1 PC

More detailed information can be found in Description section below. 

This Tempering furnace Heater is compatible with IPSEN Tempering furnaces (D/DC type), used to gether with 5 inch Radiation tube


Basic Information of the Product:

  • Flange Diameter:   5 inch
  • Rated Power:    11.5 kW
  • Rated Voltage:   110V
  • Cold segment protetion: Insulation protected
  • Insulation material:   Ceramic Fibre board insulation material
  • length(in radiation tube):      1287mm
  • hot segment length:             1005mm
  • Installation Flange diameter: 127mm
  • Heating element diameter: 114mm

Heating wire: The raw material type of the Heating wires is 0Cr21Al6Nb, max working temperature can be up to 1300°C, Longer life cycle after surface pre-oxydation process


Ceramic support pieces: are bound to withhold temperature up to 1500°C, and every batch of ceramic pieces has been tested with over 50 times of thermo-shocks


Compatible with IPSEN High termperature Tempering Furnaces and Nitriding Furnaces D/DC, furnace load size L X W X H, in mm

  • D/DC - 5, Load size: 910 X 610 X 610, load weight: 500 kg


RELIABILITY:when a heater is working in the furnace, electrical current tends to concentrate on the surface of the heating wires, this distribution of AC current density is known as the skin effect. In an ideal world, if the furface of the heating wire is perfectly smooth without defect, the current density over whole surface is evenly distributed across it. In practice, however, any defect on the surface of the wire will leads to higher concentration of current density and increases the speed of oxydation of the wire and reduces its life time. Therefore, in order to increase its stability, Nesdra selected HRE heating wire, thanks to its high standard of surface quality control, the wire can stably work when surface power density reaches 3 W/cm2

TRACEABILITY:We know that the surface quality is critical to the quality of the heating elements, we pay extra attention to any minor details during production that may cause any defects on the wire: Not only that wires are carefully checked during incoming inspection, but also that no metal tools are allowed during whole production to protect the wire from any scrach. With the serial numbers marked on each of our heaters, you can trace back to any records in production, and the records are available across the whole warranty period

USER-FRIENDLY:Normal Electric Heaters are heavy, most of them are weighting over 20 kg. In addition to the fact that heaters are not easy to haul with cranes due to its design, most maintenance workers find it difficult, if not painfu, to change heaters with their bare hands. Nesdra purposefully improved the design of heaters by applying thinner ceramic support plates and reduces their quantity, without impacting the performance, reducing the weight by 5kg -- a big improvement for maintenance!


We provide Two year warranty for the product, under following conditions:

  • if the Heaters are short circuit 

following conditions should be met to allow warranty fully granted :

  • the heaters have to be only used in pairs with Nesdra radiation tubes 
  • regular inspection and maintenance should be done properly during usage and differences between 3 phases of incoming power should be less thatn 3% 
  • the furnace is used within its designed range 


  • SAME DAY SHIPPING: The product can be shipped on the same day if the following conditions are fulfilled: it is in stock, the order is paid before 14:00 and express shipping is selected. Otherwise the order will be shipped next work day after the order is received and paid.
  • PACKING: the Heaters are packed with foaming materials to prevent from damage during transportation the components are packed in wooden boxes if quantity is smaller than 3 pieces, extra shipping cost will be charged

6, 30 day return policy

This product is subjected to our 30 day return policy. If you have any concern regarding the product after order, you may apply for returning it back to us within thirty days after the order day as long as the product is not used and original package is unbroken and can still be used and re-sell

More Information
Gross Weight (kg) 13.000000
Compatible Part Number KB-070580-C
Equipment Type High Temperature Temper
Equipment Load Size 5#
Diameter (mm) 5 inch
Power or Capacity 11.5
Working Temperature (°C) 750
Length of Work Segment (mm) 1287
Return period 30 days
Write Your Own Review
You're reviewing:Basic Heater 11.5kW 110V - SC117x1287
Your Rating